Showing posts with label GNS3. Show all posts
Friday, 30 May 2014
EtherChannel
,
GNS3
,
Load Balancing
,
Networking
,
Protocol
,
switch
,
Traffic
,
VLAN
No comments
Etherchannel in GNS3
The method to increase the bandwidth by aggregating or bundling parallel links is known as EtherChannel.
To confirm working of this lab, 192.168.1.1 ip should ping from 192.168.1.2 ip address.
In this topology all the ports are...
Read moreThursday, 29 May 2014
GNS3
,
Networking
,
switch
,
VLAN
No comments
Inter vlan routing on GNS3
VLAN is the part of switching in networking, it is essential part of switch. Basically VLAN divides the switch into parts. VLANs are isolated from one from each other so that packets in one VLAN cannot communicate with other VLAN.
To...
Read moreWednesday, 21 May 2014
BGP
,
GNS3
,
IPv6
,
MPLS
,
Networking
No comments
IPv6 Tunnel over MPLS & eBGP Network
In this lab, same concept, IPv6 tunneling is used, as it is used in my previous lab IPv6 Tunnel over IPv4 Network. Concept of making tunnel over the network is same but in both the topologies network is different. In my previous lab...
Read moreTuesday, 20 May 2014
EIGRP
,
GNS3
,
IPv6
,
Networking
No comments
IPv6 Tunnel over IPv4 Network
In this topology IPv6 tunnel is made over IPv4 network, color dark red representing
the IPv4 network whereas color blue is showing IPv6 Network with IPv6
tunnel. EIGRP routing protocol is used for communication between both
network...
Read moreFriday, 16 May 2014
%DUAL-5-NBRCHANGE: IP-EIGRP(0)
I searched everywhere on internet about this error. I faced this error yesterday, on internet i found that this error is due to MTU packet size. It is quite surprising for me that MTU is creating problem, because I have learned that router...
Read moreWednesday, 14 May 2014
Layer 3 Switch in GNS3
GNS3 is a cisco simulator to perform network analysis without cost. GNS3 has very good features like Router, Switch, ATM switch, Frame Relay Switch, host(vpcs) etc, but it also has a limitation in switching, all the concepts of switching...
Read moreSunday, 11 May 2014
Protocols Redistribution
Internet constitutes with different -2 protocols, so, to advertise routes from one protocol to another protocol redistribution process is used.
In this topology Redistribution_point router is the mid point of the topology,...
Read moreSaturday, 10 May 2014
DHCP server on Switch in GNS3
DHCP server is the server which provides IP address dynamically to the host. In GNS3 IOS 3725 image is used as Layer 3 Switch. It has NM-16ESW slot which has 16 fastethernet ports.
In this topology R1 is Layer 3 switch and SW1 is Layer...
Read more
Add IOS image to GNS3
To use GNS3 in a proper manner, then one needs to know how to add IOS Image to GNS3. Because if a person do not know to add IOS image in GNS3 then he can not use Router, Switches and other features of the GNS3.
To add IOS image to GNS3,...
Read moreFriday, 9 May 2014
Connect GNS3 with Linux
This post assumes that reader has basic knowledge of GNS. For those who does not know they can visit GNS3 official website www.gns3.net.
To communicate GNS3 with Linux, simple steps have to follow :-
1. Create loopback interface.
2. IP...
Read moreTuesday, 6 May 2014
IPv6 DNS Server on Linux
IPv6 DNS Name Resolution
IPv6 is of 128 bits, and each slot is of 16 bits, separated by column (:). It is very difficult to remember 128 bits address for each host and for each website. So Name Resolution can be done through DNS server.
...
Read more
Subscribe to:
Posts
(
Atom
)